Cái ổ cứng của em bị lỗi!! cắm vào vẫn nhận ra!! Nhưng khi chép hay đọc thì rớt liên kết liên tục!! dưới đây là em dùng phần mềm kiểm tra phần mềm!! tất cả các mục đều xanh ngoại trừ 3 mục có dấu chấm than màu vàng!![em có để dấu chấm than ở mấy chỗ đó]; Ai biết nó bị gì và sửa sao chỉ em với!! em có nhiều dữ liệu và muốn sửa để sử dụng tiếp!! Em đoán là do vấn đề tản nhiệt ko tốt nên nó bị vây!! Em cám ơn nhiều!! HDDScan S.M.A.R.T. Report
Model: ST3500320AS Firmware: SD81 Serial: 5QM3CWKA LBA: 976773168
Report By: HDDScan for Windows version 3.2 Report Date: 3/11/2010 11:02:18 PM
Model: ST3500320AS Firmware: SD81 Serial: 5QM3CWKA LBA: 976773168
Report By: HDDScan for Windows version 3.2 Report Date: 3/11/2010 11:02:18 PM
Num Attribute Name Value Worst Raw[hex] Threshold
001 Raw Read Error Rate 093 083 000009BA-804D 006
003 Spin Up Time 091 089 00000000-0000 000
004 Start/Stop Count 100 100 00000000-0378 020
!005 Reallocation Sector Count 100 100 00000000-07F9 036
007 Seek Error Rate 064 060 00010028-21BE 030
009 PowerOn Hours Count 100 100 00000000-021C 000
010 Spin Retry Count 100 100 00000000-000B 097
012 Device Power Cycle Count 100 100 00000000-019E 020
184 End To End Error Count 100 100 00000000-0000 099
!187 Reported Uncorrectable Error 001 001 00000000-06DB 000
!188 Reported Command Timeouts 100 099 00010001-0001 000
189 High Fly Writes 099 099 00000000-0001 000
190 Airflow Temperature 061 040 39 C 045
190 Airflow Temperature Minimum 061 040 27 C 045
190 Airflow Temperature Maximum 061 040 39 C 045
190 Airflow Overheated Count 061 040 109 045
194 HDA Temperature 039 060 39 C 000
194 HDA Temperature Minimum 039 060 21 C 000
194 HDA Temperature Maximum 039 060 40 C 000
195 Hardware ECC Recovered 042 037 000009BA-804D 000
197 Current Pending Sector Count 100 100 00000000-0006 000
198 Uncorrectable Sector Count 100 100 00000000-0006 000
199 UltraDMA CRC Errors 200 200 00000000-0000 000
Về hãng ổ cứng thì anh tin tưởng Seagate hơn vì tỉ lệ hư hỏng thấp. Toshiba cũng đáng tin vì hãng này chủ yếu đánh vào mảng enterprise [cần độ tin cậy cao]. Mà với đồ điện tử thì nhiều khi... hên xui vì hầu hết sản phẩm của các hãng lớn đều chạy tốt, chỉ có một tỉ lệ nào đó không, và “tình cờ” mình mua trúng cái đó.
It may be the result of the problem - but the opposite is possible: the hard disk had weak sectors due to the BSOD [or more precisely the unfinished write operation, caused by the power loss]. This is more common: due to the power loss [by the reset / forced shut down] the hard disk may not be able to finish the write and then it may record some special values in the error-counters [the 65528 indicates that, it seems an underflow condition].
This post mainly discusses what does uncorrectable sector count mean for your hard drive and how to cope with this case. Now, let’s explore these contents together.
On This Page :
What Does Uncorrectable Sector Count Mean
If there are any bad sectors on your hard drive, some errors such as Windows couldn’t be installed error 0x80300024, path not found c boot may happen to you. What does uncorrectable sector count mean? Do I need to change a new drive when this happens to your drive? You may raise such a question. Here, MiniTool will tell the answers.
If you conduct a non-destructive scanning, you will not receive any serious issues or warnings. However, some disks have been marked as suspicious due to uncorrectable sectors. There’s no sector reallocations and no pending sectors. In this case, uncorrectable sector count means that your disk probably is safe.
SMART ID 198 [0xC6] Uncorrectable Pending Sector Count is an important S.M.A.R.T parameter, which indicates many uncorrectable errors when reading/writing a sector on the hard drive. The error can damage or does a permanent failure to the hard drive and lead to data loss.
Simply put, offline uncorrectable pending sector count warning implies imminent disk failure and requires immediate backup and drive replacement. Here is a full guide to fix hard drive uncorrectable sector count warning.
4 Phases to Fix Uncorrectable Sector Count Warning
Warnings like uncorrectable sector count 100, off-line uncorrectable sector count will appear when you are trying to obtain the SMART information of a disk by utilizing tools like Drive Monitor, CrystalDiskInfo, HDSentinel and so on. Hence, it is strongly recommended that you monitor the disk SMART parameter actively to prevent data loss because of impending drive.
To fix the SMART uncorrectable sector count warning, you need to know something about it.
- SMART ID 5 [0x05]:Relocated Sectors Count
- SMART ID 187 [0xBB]:Reported Uncorrectable Errors
- SMART ID 188 [0xBC]:Command Timeout
- SMART ID 197 [0xC5]:Current Pending Sector Count
- SMART ID 198 [0xC6]:Uncorrectable Sector Count
Now, you can follow the steps below of this uncorrectable sector count fix with minimum data loss.
Phase 1: Back up and Recover
If you can access the drive, please back up files immediately. If the drive turns RAW or unavailable, you can fix this issue and recover the missing data by utilizing methods from this post.
Phase 2: Perform Surface Test
You are able to test each drive sector or memory block for the read/write response during the surface test. Here, MiniTool Partition Wizard is strongly recommended for you. Its Surface Test enables you to check whether there’s any sector on your hard drive with ease.
To get detailed steps to perform surface test on MiniTool Partition Wizard, you can read this post: Top 4 Free Hard Drive Test Tools Every Windows Users Must Know
Phase 3: Run CHKDSK
After running surface test for the drive, you should run CHKDSK to scan and repair bad sectors. Here are steps to run CHKDSK.
Step 1: Type command prompt in the search box, and then right click Command Prompt from the search results and choose Run as administrator.
Step 2: In this pop-up prompt window, type the command chkdsk *: /f /r [* stands for the volume that you want to check] and hit the Enter key. If there are more than one volume on the disk, please run the above command one by one.
Tip: As you have backed up data in advance, you can delete all the volumes on the disk and then run the scanning to fix SMART uncorrectable sector count warning.
Phase 4: Full Format or Erase Drive Securely
If you still see the uncorrectable sector count warning in SMART information of the disk, you can utilize a safe eraser software such as MiniTool Partition Wizard for file or format the affected drive.
Full format and safe eraser will overwrite each sector on the drive. This operation will force the drive into reading the SMART parameters and attributes including uncorrectable sector count.
Before formatting your drive, you need to know what does formatting a hard drive do. Then follow the steps below to perform a full format.
Step 1: Press Win and R keys to open the Run window, and then type diskmgmt.msc and hit the Enter to open your Windows Disk Management.
Step 2: Right click the affected drive volume in the Disk Management page, and then select the Format option from the elevated menu.
Step 3: Uncheck Perform a quick format and click OK to save the change. Then the volume will be formatted automatically.
Tip: If you don’t uncheck Perform a quick format, the data can be recovered with recovery software.
About The Author
Position: Columnist
Having writing articles about computer tech for a long time, I am rather experienced especially on the aspect of computer optimization, PC enhancement, as well as tech terms explanation. The habit of looking through tech forums makes me a great computer issues collector. And then, many articles related to these issues are released, which benefit plenty of users. Professional, effective, and innovative are always the pursuit of an editing worker.